Since your previous stereo was smaller than your new iRV RV Stereo # IRV64FR your only option is to trim out the opening larger to fit the new stereo. I recommend trimming the lower panel below the current stereo down as this will look more aesthetically pleasing. view full answer...
Yes, the iRV RV Stereo # 292-101809 does need 12 volt power to work. Each of the in-wall stereos do require 12 volt power. I have added a link to a video review of this stereo as well as a link to our entire selection of RV stereos for you to take a look at. view full answer...
The iRV RV Stereo part # 292-101809 is an excellent option with wireless remote, Bluetooth compatibility, AM/FM stereo, and AUX ports. It can read and play CD's and DVD's but not BluRay. There are no RV stereos which play BluRay. view full answer...
The Jensen RV Stereo part # JWM40 is a great stereo for your RV that will allow you to play CD's, DVD's, and other devices connected through Bluetooth. That said, it is not BluRay compatible nor are any of the other RV stereos that I am aware of for that matter. view full answer...
Due to the wide variety of mounting locations there isn't a specific mounting plate available for the iRV RV Stereo # IRV64FR, or any other stereo for that matter. What most people do is get a piece of wood and stain/paint it to match the cabinet the stereo is going in and use it to cover the larger hole and cutout of just what's needed to mount the stereo into it. view full answer...
The iRV RV Stereo part # 292-101079 is as the title states an RV stereo. It is designed to be installed in a trailer which usually requires splicing of wires. If you were to install the stereo in another application like a vehicle then this can be done but again splicing will be needed. There are certain stereos that can offer plug and play instillation for certain vehicles but we don't offer any options for this as this is not a product category we specialize in. view full answer...
If you have an iRV stereo like the iRV RV Stereo - Single DIN # 292-101809 then you would need to press and hold the "Clock" button for 3 seconds to adjust the hours with the "Volume Knob". Simply turn the knob until the AM switches to PM and then you can press the "Volume Knob" in to switch over to the minutes setting.
If you have a different model iRV stereo then let me know and I can help walk you through changing the time on your model. view full answer...
It sounds like you're asking if the Jensen Merchless RV Stereo, part # JWM10A, can link to bluetooth speakers, or if they need to be hardwired.
This stereo does in fact need to be hardwired to speakers. The bluetooth function of this stereo is meant as a receiver, not as a transmitter. view full answer...
The iRV RV Stereo part # 292-101079 does not have an optical input but we do have a similar option that does, the iRV RV Stereo part # iRV34. view full answer...
It sounds like you're wanting to install the Jensen RV Stereo # JWM60A to replace an MP5000 stereo or vice versa; these two stereos have similar mounting dimensions but the wiring will be different between the two units. I have added a diagram of the wiring for the Jensen RV Stereo # JWM60A for you to use as a reference. view full answer...
For a stereo like the Furrion Mechless RV Stereo DV7200 or any others like the # DV3300SBL you would need to set the source on the stereo to HDMI using either the remote or button on the face of the stereo for it to play audio from an electronic that's connected to it via HDMI. view full answer...
Pretty much every stereo (even within the same brand) uses a different wire harness for their stereo's so installing the Jensen RV Stereo w DVD Player # JWM60A will require you to do a bit of wiring. You'll just want to get the wiring diagram for both units and swap over one function at a time from the old wire harness to the new one. I've attached both wiring diagrams below as well as one of my installation videos for another stereo system where I show this process. view full answer...
The iRV RV Stereo w/ DVD Player # IRV64FR has a yellow 12v power wire that's intended to provide power to the stereo to retain the memory so that your preset stations and clock are there when you turn the stereo on. The red ACC wire is to power the other stereo functions and is intended to be tied into an ignition switch so that the stereo only has power when the vehicle it's in is running to prevent unwanted drain on the battery. This is great for motorhomes but can cause some confusion... view full answer...
The back light of the iRV RV Stereo w/ DVD Player # 292-101809 unfortunately can't be turned off without turning the stereo off as well. view full answer...
The Jensen RV Stereo part # JWM60A is not a plug and play replacement for the Concertone RV Stereo ZX75 as they are made by two different manufactures. However, it will be easy to replace this as all you will have to do is splice the new wiring harness onto your trailer in place of the above. I have attached a diagram of this for you which should be a simple, pain free task. The only other thing you will need are butt connectors, part # DW05744-10 (2). view full answer...
The iRV RV Stereo w/ DVD Player - Single DIN - App Control, Bluetooth, HDMI, USB # 292-101809 can not be connected to a Bluetooth speaker. This stereo was designed to be wired into up to 6 speakers.
The Bluetooth capabilities are referring to you to connecting your smartphone to the stereo and playing the audio from the connected speakers.
I have attached a wiring diagram for you to check out as well. view full answer...
The simplest way to accomplish getting the speakers all through the rv for the sound on the tv is to use the Jensen Stereo Audio/Composite Video Cable # JCAV50. There should be a white and red audio input on the back of your tv, plug them in.
On the rear of the Jensen Stereo Bluetooth # JWM60A plug in the other end of the red and white cables. Change the input option on the Jensen Stereo to AUX or Auxiliary. At this point any sound that plays through your TV should play through the speakers... view full answer...
To remove the iRV RV Stereo - Single DIN part # 292-101809 you will need to remove the snap on end cap on each side. Behind these you will find the two mounting screws on each side which can be removed giving you the access yu need behind the stereo. view full answer...
I spoke with Jensen about the Jensen Touch Screen RV Stereo part # VX4022ARTL and they informed me that when you have the stereo hooked up to the TV and are playing a DVD, the sound would either be played out of the stereo or the TV, whichever setting you choose on the TV but not both not matter which data cable you are using. According to Jensen, this is not possible with any of their stereos nor do we have any others that will. I am also not sure they make a stereo with this feature.... view full answer...
Stereos are definitely not standardized when it comes to size so alterations will typically be required unless you replace a stereo with the same make and model you had previously. The Jensen RV Stereo w DVD Player # JWM60A is a bit bigger than most requiring a 9" wide x 6" tall x 5-1/2" deep cutout hole. If your cutout hole is too small then you would either have to cut the current hole larger or switch to a smaller unit.
If your current hole is much larger then I typically will get... view full answer...
Go To Results